| View previous topic :: View next topic |
| Author |
Message |
gaillarry
Big Brick Rider
Joined: 18 Apr 2010
Posts: 65
Location: Ontario, Canada
|
 Posted: Sun May 23, 2010 12:21 pm Post subject: Installing the Fairing |
 |
|
Putting the fairing back on the bike, been 2 months so forgot where a few parts go. Pic 1 is the spring loaded lever on each fairing box. How do they install?
Pic 2 is two rubber parts.
Pic 3 is these two rail things?
 [/img]
_________________
1997 K1100GT |
|
| Back to top |
|
 |
dave n
Flying Brick Rider
Joined: 13 Dec 2003
Posts: 316
Location: Gastonia NC
|
| Posted: Sun May 23, 2010 2:31 pm Post subject: ??? |
|
|
the rail things look like a broken saddle bag hinge.
_________________
Dave Norris KOG 248
1999 Cagiva Gran Canyon
1993 K1100LT w/Hannigan sidecar
2008 Suzuki DR650 |
|
| Back to top |
|
|
beemeerr11
Flying Brick Rider
Joined: 05 Mar 2006
Posts: 168
|
| Posted: Mon May 24, 2010 8:10 am Post subject: Re: Installing the Fairing |
|
|
| gaillarry wrote: | Putting the fairing back on the bike, been 2 months so forgot where a few parts go. Pic 1 is the spring loaded lever on each fairing box. How do they install? leave it as is, 2 self tapping screws hold the glovebox/knee pad part, the lid pushes down on it and snaps shut
Pic 2 is two rubber parts?
They fit under your glove boxes, you will see the three holes where you will need to put 2 screws and 1 bolt and nut that fastens the upper fairing to the lower fairing
Pic 3 is these two rail things?
[/img] |
Last edited by beemeerr11 on Mon May 24, 2010 8:16 am; edited 1 time in total |
|
| Back to top |
|
|
gaillarry
Big Brick Rider
Joined: 18 Apr 2010
Posts: 65
Location: Ontario, Canada
|
| Posted: Mon May 24, 2010 8:15 am Post subject: |
|
|
Got the lid parts figured out. The two large rubber pieces still have me baffled. Hopefully I'll have the bike done today and take her for a test ride!!!
_________________
1997 K1100GT |
|
| Back to top |
|
|
Scott_Anderson
Site Admin
Joined: 05 Sep 2006
Posts: 3122
Location: Central Iowa, USA
|
| Posted: Mon May 24, 2010 8:29 am Post subject: |
|
|
The large rubber parts in your 2nd pic, mount under the fairing boxes. They are mounted with the soft rubber against the fuel tank. They mount with a couple of the screws that also hold the lower section of the fairing to the upper section.
The oblong notch that goes towards the "outside edge" is where you run the wires for the guages.
I also agree that it looks like your 3rd pic is broken hard bag hinges.
_________________
Ride safe.
1995 K1100LT 0302044
2017 FLHTK Ultra Limited
Garmin StreetPilot 2820
Garmin Zumo 550
Garmin Zumo XT
"One who does not ask questions is ashamed to learn" Danish proverb
1997 K1100LT 0302488(R.I.P.)
1997 R1100RT ZC62149(sold) |
|
| Back to top |
|
|
gaillarry
Big Brick Rider
Joined: 18 Apr 2010
Posts: 65
Location: Ontario, Canada
|
| Posted: Mon May 24, 2010 10:18 am Post subject: |
|
|
Thanks, its all back together, except for the rubber things. I take it for a test ride then put the rubbers on.
_________________
1997 K1100GT |
|
| Back to top |
|
|
miKeinWIs
Mad Brick Rider
Joined: 29 Jun 2009
Posts: 143
Location: Birchwood, WI
|
| Posted: Tue May 25, 2010 6:07 am Post subject: |
|
|
The two straight Vee shaped pieces go on the end of each side panel, front part by the engine.
Easily lost...
Good luck
Mike
_________________
'97 K1100LT
Bought 6/30/09 w/26,750 miles |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
