| View previous topic :: View next topic |
| Author |
Message |
joeangi Flying Brick Rider

Joined: 03 Apr 2006 Posts: 291 Location: Westchester, New York
|
Posted: Tue Feb 03, 2009 10:56 am Post subject: Still can't get fork apart |
|
|
I am still having problems getting my fork slider out from the leg. All the guts are out. It appears that the wiper on the bottom of the fork tube is stuck on the fork seal. I cannot get the fork seal to come out. I have tried heat, I have tried to tap the slider from the bottom. It is really stuck.....help.
Joe |
|
| Back to top |
|
 |
Rider Flying Brick Rider
Joined: 05 Apr 2003 Posts: 222 Location: La Grande, OR
|
Posted: Tue Feb 03, 2009 3:18 pm Post subject: Fork work |
|
|
Joe,
OK, let's try this. I assume you have taken the snap ring out. That's tough to do with the tube still in the slider. Then mount the slider in a good vice by the brake bosses. If you have lead overlays for the vice so much the better. I would suggest heating the area around the seal with a heat gun before starting the next step. Next, push the tube to the bottom of the slider and with a good grip on the tube pull it smartly back to the jam point. You can start out fairly gently and keep track of weather the seal begins to move. Keep working on it and put more arm into it if needed. Work it like a slide hammer.
You may have to replace a bushing when you put it back together. Also, think about installing gaiters too.
Good luck,
Ed _________________ 2007 650 Burgman, 2003 400 Burgman
Some days you get the bear, some days the bear gets you. |
|
| Back to top |
|
 |
joeangi Flying Brick Rider

Joined: 03 Apr 2006 Posts: 291 Location: Westchester, New York
|
Posted: Tue Feb 03, 2009 8:15 pm Post subject: |
|
|
Dear Ed,
Thanks for the advice. That is what I have been trying...and I can't get the damn fork seal to move. I think that there is some heavy duty corrosion down in the leg. The tube does not even go down all the way...I think the walls are a mess. I have been spraying it with WD40 and trying to get it to move...but nothing yet. I sprayed it with a lot of PB Blaster tonight and am letting it sit. I have tried heating until the fork seal is smoking. I can get the fork tube up until I can see a hole, but no further. I have pulled so hard, that I think I might hurt the fork leg. Yes the snap ring is out, but it feels like I am hitting metal, when I use it as a slide hammer.
I will try again tomorrow after letting the PB work all night.
Thanks,
Joe |
|
| Back to top |
|
 |
Scott_Anderson Site Admin
Joined: 05 Sep 2006 Posts: 3128 Location: Central Iowa, USA
|
Posted: Tue Feb 03, 2009 8:45 pm Post subject: Re: Still can't get fork apart |
|
|
| joeangi wrote: | I am still having problems getting my fork slider out from the leg. All the guts are out. It appears that the wiper on the bottom of the fork tube is stuck on the fork seal. I cannot get the fork seal to come out. I have tried heat, I have tried to tap the slider from the bottom. It is really stuck.....help.
Joe |
you've got 2 "wipers"(guide bushings) in there. 1 in the lower fork tube under the seal with a metal seal support ring between them and a wiper on the bottom on the fork slider as well. These bushings are split, so if the one on the fork slider has started to "spread" it may not slide thru the one in the lower fork tube.
Like Rider suggest keep working it like a slide hammer, 1 or the other will give eventually.
It took me quite a bit to get my seals out by them selves when I took mine apart, and my sliders came out of my lowers. _________________ Ride safe.
1997 K1100LT 0302488
2017 FLHTK Ultra Limited
Garmin StreetPilot 2820
Garmin Zumo 550
Garmin Zumo XT
"One who does not ask questions is ashamed to learn" Danish proverb
1995 K1100LT 0302044(R.I.P.)
1997 R1100RT ZC62149(sold) |
|
| Back to top |
|
 |
joeangi Flying Brick Rider

Joined: 03 Apr 2006 Posts: 291 Location: Westchester, New York
|
Posted: Tue Feb 03, 2009 9:39 pm Post subject: |
|
|
Dear Scott,
Just took the other fork apart...no problems. I agree with your assessment. I wanted to see what it looked like in there. I think that the two metal bushings are hitting each other and not allowing any movement. I have the other fork leg at work soaking...so will check tomorrow. What do you think about sliding a thin piece of plastic (Plastistruck?) down between the slider and the fork seal to help ease those two bushing past each other? |
|
| Back to top |
|
 |
Mystic Red Flying Brick Rider

Joined: 28 Mar 2005 Posts: 2330 Location: Twin Lakes Idaho
|
Posted: Tue Feb 03, 2009 9:55 pm Post subject: |
|
|
Wow, and I thought the snap rings were tough.  _________________ Scott Hespelt, '94 K11LT
K11 OG #466 |
|
| Back to top |
|
 |
Scott_Anderson Site Admin
Joined: 05 Sep 2006 Posts: 3128 Location: Central Iowa, USA
|
Posted: Tue Feb 03, 2009 10:06 pm Post subject: |
|
|
| joeangi wrote: | Dear Scott,
What do you think about sliding a thin piece of plastic (Plastistruck?) down between the slider and the fork seal to help ease those two bushing past each other? |
Well I'm not sure what that is but I did also think if you have some old 35mm film negative, that might work as well. 2-3 pieces around the tube like a shoe horn. _________________ Ride safe.
1997 K1100LT 0302488
2017 FLHTK Ultra Limited
Garmin StreetPilot 2820
Garmin Zumo 550
Garmin Zumo XT
"One who does not ask questions is ashamed to learn" Danish proverb
1995 K1100LT 0302044(R.I.P.)
1997 R1100RT ZC62149(sold) |
|
| Back to top |
|
 |
joeangi Flying Brick Rider

Joined: 03 Apr 2006 Posts: 291 Location: Westchester, New York
|
Posted: Wed Feb 04, 2009 7:55 pm Post subject: |
|
|
| Well...still can't get them apart. I tried the film thing, got them to slide in, but they fell apart before the tube came out. From all my measuring, it appears the wiper on the fork tube is hitting the spacer ring. It looks like it should pop right out by looking at the other leg. I tried heating the heck out of it (with propane torch). Last night it sat all night with pb blaster. I am getting obsessed, and frustrated at the same time. I really don't want to have to buy a new fork leg....and to think, all I wanted to do was clean out the fork legs, and change the seals.... |
|
| Back to top |
|
 |
joeangi Flying Brick Rider

Joined: 03 Apr 2006 Posts: 291 Location: Westchester, New York
|
Posted: Wed Feb 04, 2009 9:40 pm Post subject: |
|
|
| Update...some progress, got the fork seal out, as well as the bushing. Still can't get the fork leg out! There is a small machined section, just below the groove for the bushing. The fork slider bushing appears to be hanging up on that.....I think I need professional help. |
|
| Back to top |
|
 |
joeangi Flying Brick Rider

Joined: 03 Apr 2006 Posts: 291 Location: Westchester, New York
|
Posted: Thu Feb 05, 2009 6:40 pm Post subject: |
|
|
| Update....got the fork apart today....went to the local metal shop. He put a rod down through the leg and put a washer to protect the fork cap, and basically pounded it out. The lower bushing had gone off the machined section, and had become like a locking collet. Every time you pulled it would flare out and lock harder. I just ordered all new bushings and fork seals so all should be well. Thank you all that lent advice! In the end this was a unusual one. |
|
| Back to top |
|
 |
|