View previous topic :: View next topic |
Author |
Message |
Flying Duck PsyKotic Waterfowl
Joined: 27 Jan 2005 Posts: 10087 Location: Bumf***, WA
|
Posted: Sun Apr 29, 2018 7:33 pm Post subject: |
|
|
So, you got the bottom part of the switch out w/o drilling? Have you been able to get a replacement part back in yet? _________________ 93 LT (x2)
94 RS
86-97 K75F(K75/100/1100 Frankenbrick)
86 K75C w/paralever, hi perf cams,TURBO!
91 & 92 K75Ss
91 K1
86 custom K100
14 WR250R
IBA #17739 (SS1K, BBG, 50CC)
Buy parts HERE |
|
Back to top |
|
|
Al. Flying Brick Rider
Joined: 28 Oct 2005 Posts: 383 Location: West of Ireland
|
Posted: Mon Apr 30, 2018 6:18 am Post subject: |
|
|
Flying Duck wrote: | So, you got the bottom part of the switch out w/o drilling? Have you been able to get a replacement part back in yet? |
The grub screw is accessible when r.h. box is removed.
The clue in an old post was the red paint, I presume
worked as a Locktite
It's in the mail system....
I think I'll be able to line up the switch based on position of old one.
But I'm guessing you have a hint..
What do I use instead of red paint - superglue????? _________________ 1994 K1100 LTSE + Blackbird |
|
Back to top |
|
|
Scott_Anderson Site Admin
Joined: 05 Sep 2006 Posts: 3119 Location: Central Iowa, USA
|
Posted: Mon Apr 30, 2018 7:30 am Post subject: |
|
|
I wouldn't use superglue..... I'd use some paint again were it me. Something that will hold the screw in place yet easily removable if needed. _________________ Ride safe.
1995 K1100LT 0302044
1997 R1100RT ZC62149
2017 FLHTK Ultra Limited
Garmin StreetPilot 2820
Garmin Zumo 550
Garmin Zumo XT
"One who does not ask questions is ashamed to learn" Danish proverb
1997 K1100LT 0302488(R.I.P.) |
|
Back to top |
|
|
Al. Flying Brick Rider
Joined: 28 Oct 2005 Posts: 383 Location: West of Ireland
|
Posted: Tue May 01, 2018 4:48 pm Post subject: |
|
|
All reconnected and working.
No road test yet but I don't expect issues.
Thankx for advice _________________ 1994 K1100 LTSE + Blackbird |
|
Back to top |
|
|
Flying Duck PsyKotic Waterfowl
Joined: 27 Jan 2005 Posts: 10087 Location: Bumf***, WA
|
Posted: Wed May 02, 2018 1:00 am Post subject: |
|
|
I'd use 5 minute epoxy. It will stay in place but can be picked out pretty easily when necessary.
Were you able to get that lower switch assembly out and back in without messing with the fork trees? (I think my 94 RS is having issues with that or its wiring.) _________________ 93 LT (x2)
94 RS
86-97 K75F(K75/100/1100 Frankenbrick)
86 K75C w/paralever, hi perf cams,TURBO!
91 & 92 K75Ss
91 K1
86 custom K100
14 WR250R
IBA #17739 (SS1K, BBG, 50CC)
Buy parts HERE |
|
Back to top |
|
|
Al. Flying Brick Rider
Joined: 28 Oct 2005 Posts: 383 Location: West of Ireland
|
Posted: Wed May 02, 2018 4:23 am Post subject: |
|
|
Flying Duck wrote: | I'd use 5 minute epoxy. It will stay in place but can be picked out pretty easily when necessary.
Were you able to get that lower switch assembly out and back in without messing with the fork trees? (I think my 94 RS is having issues with that or its wiring.) |
Once the box on rh side was out you could see the grub screw.
It's a fine slot in the screw and screw very tiny.
I had to pick out the red paint with like a dentists tool.
I put a cloth under it before removing it with a tweezrs with a touch of grease on them and dipped the screwdriver in a tiny bit of grease putting it back in.
The switch dropped down easily enough and went up very easily.
I was sorry I didn't take pics of cable route just to be sure.
It seems to do a lot of flexing particularly on full lock left.
The switch had two "pins" to locate it. One is a round and the other rectangular. If you note positions of key and slot in switch it should go back ok. _________________ 1994 K1100 LTSE + Blackbird |
|
Back to top |
|
|
Al. Flying Brick Rider
Joined: 28 Oct 2005 Posts: 383 Location: West of Ireland
|
Posted: Wed May 02, 2018 4:23 am Post subject: |
|
|
Flying Duck wrote: | I'd use 5 minute epoxy. It will stay in place but can be picked out pretty easily when necessary.
Were you able to get that lower switch assembly out and back in without messing with the fork trees? (I think my 94 RS is having issues with that or its wiring.) |
Once the box on rh side was out you could see the grub screw.
It's a fine slot in the screw and screw very tiny.
I had to pick out the red paint with like a dentists tool.
I put a cloth under it before removing it with a tweezrs with a touch of grease on them and dipped the screwdriver in a tiny bit of grease putting it back in.
The switch dropped down easily enough and went up very easily.
I was sorry I didn't take pics of cable route just to be sure.
It seems to do a lot of flexing particularly on full lock left.
The switch had two "pins" to locate it. One is a round and the other rectangular. If you note positions of key and slot in switch it should go back ok. _________________ 1994 K1100 LTSE + Blackbird |
|
Back to top |
|
|
Al. Flying Brick Rider
Joined: 28 Oct 2005 Posts: 383 Location: West of Ireland
|
Posted: Wed May 02, 2018 6:57 am Post subject: |
|
|
Flying Duck wrote: | I'd use 5 minute epoxy. It will stay in place but can be picked out pretty easily when necessary.
Were you able to get that lower switch assembly out and back in without messing with the fork trees? (I think my 94 RS is having issues with that or its wiring.) |
I sent a pm - I think...... _________________ 1994 K1100 LTSE + Blackbird |
|
Back to top |
|
|
|