View previous topic :: View next topic |
Author |
Message |
Al. Flying Brick Rider
Joined: 28 Oct 2005 Posts: 383 Location: West of Ireland
|
Posted: Thu Oct 12, 2017 3:18 pm Post subject: Spare washer |
|
|
Fitted new air filter on 1994 K1100 LTSE
When job was done there was this big washer on the floor.
About the size of a silver dollar with shadow of small screw/bolt head.
I know it but cannot figure where it belongs.
Wasn't prepared to dismantle other side to fond out.
Tank retaining circlip took to the air..........
4 in the post now _________________ 1994 K1100 LTSE + Blackbird |
|
Back to top |
|
|
Flying Duck PsyKotic Waterfowl
Joined: 27 Jan 2005 Posts: 10085 Location: Bumf***, WA
|
Posted: Thu Oct 12, 2017 4:21 pm Post subject: |
|
|
Maybe the bracket that holds the right lower to the side of the engine? _________________ 93 LT (x2)
94 RS
86-97 K75F(K75/100/1100 Frankenbrick)
86 K75C w/paralever, hi perf cams,TURBO!
91 & 92 K75Ss
91 K1
86 custom K100
14 WR250R
IBA #17739 (SS1K, BBG, 50CC)
Buy parts HERE |
|
Back to top |
|
|
Grunter Flying Brick Rider
Joined: 30 Sep 2015 Posts: 368 Location: North East England
|
Posted: Thu Oct 12, 2017 5:34 pm Post subject: |
|
|
Flying Duck wrote: | Maybe the bracket that holds the right lower to the side of the engine? |
That sounds pretty well what I would suggest. Actually there should be 2 washers but one tends to stick to the rubber support on the fairing. _________________ 1997 K1100LT
1994 R1100RS |
|
Back to top |
|
|
Grunter Flying Brick Rider
Joined: 30 Sep 2015 Posts: 368 Location: North East England
|
Posted: Thu Oct 12, 2017 5:34 pm Post subject: |
|
|
Flying Duck wrote: | Maybe the bracket that holds the right lower to the side of the engine? |
That sounds pretty well what I would suggest. Actually there should be 2 washers but one tends to stick to the rubber support on the fairing. _________________ 1997 K1100LT
1994 R1100RS |
|
Back to top |
|
|
Flying Duck PsyKotic Waterfowl
Joined: 27 Jan 2005 Posts: 10085 Location: Bumf***, WA
|
Posted: Thu Oct 12, 2017 7:42 pm Post subject: |
|
|
I was thinking of the earlier Ks. I think the K1100LT only used those big washers on the top one that's mounted to the side of the radiator. _________________ 93 LT (x2)
94 RS
86-97 K75F(K75/100/1100 Frankenbrick)
86 K75C w/paralever, hi perf cams,TURBO!
91 & 92 K75Ss
91 K1
86 custom K100
14 WR250R
IBA #17739 (SS1K, BBG, 50CC)
Buy parts HERE |
|
Back to top |
|
|
Scott_Anderson Site Admin
Joined: 05 Sep 2006 Posts: 3119 Location: Central Iowa, USA
|
Posted: Thu Oct 12, 2017 8:47 pm Post subject: |
|
|
part #6...
I have them on my lowers. _________________ Ride safe.
1995 K1100LT 0302044
1997 R1100RT ZC62149
2017 FLHTK Ultra Limited
Garmin StreetPilot 2820
Garmin Zumo 550
Garmin Zumo XT
"One who does not ask questions is ashamed to learn" Danish proverb
1997 K1100LT 0302488(R.I.P.) |
|
Back to top |
|
|
Flying Duck PsyKotic Waterfowl
Joined: 27 Jan 2005 Posts: 10085 Location: Bumf***, WA
|
Posted: Thu Oct 12, 2017 10:27 pm Post subject: |
|
|
That #6 washer has a big hole since the bolt it holds is female. (threaded on the inside to accept the the #2 M5.) _________________ 93 LT (x2)
94 RS
86-97 K75F(K75/100/1100 Frankenbrick)
86 K75C w/paralever, hi perf cams,TURBO!
91 & 92 K75Ss
91 K1
86 custom K100
14 WR250R
IBA #17739 (SS1K, BBG, 50CC)
Buy parts HERE |
|
Back to top |
|
|
Al. Flying Brick Rider
Joined: 28 Oct 2005 Posts: 383 Location: West of Ireland
|
Posted: Fri Oct 13, 2017 1:44 pm Post subject: |
|
|
Bit of a stupid question really.
I'll look again at suggestions.
Thanks for help. _________________ 1994 K1100 LTSE + Blackbird |
|
Back to top |
|
|
Flying Duck PsyKotic Waterfowl
Joined: 27 Jan 2005 Posts: 10085 Location: Bumf***, WA
|
Posted: Fri Oct 13, 2017 8:44 pm Post subject: |
|
|
I need to take a right LT lower off tomorrow to replace a failed bolt at the top of an engine protection bar so I'll snap some pics for you. _________________ 93 LT (x2)
94 RS
86-97 K75F(K75/100/1100 Frankenbrick)
86 K75C w/paralever, hi perf cams,TURBO!
91 & 92 K75Ss
91 K1
86 custom K100
14 WR250R
IBA #17739 (SS1K, BBG, 50CC)
Buy parts HERE |
|
Back to top |
|
|
Al. Flying Brick Rider
Joined: 28 Oct 2005 Posts: 383 Location: West of Ireland
|
Posted: Mon Oct 16, 2017 10:35 am Post subject: |
|
|
Thanks for that.
The washer is 1" in diameter with 1/4" hole.
Not from under fairing I don't think.
It's muddy with clean circle where bolt was and clean on back.
Offered it up to location but diameter too big, but I discovered I've
lost bolt from there now - did 629 miles at weekend, some very bad roads, almost
a track in one case.
BTW where is my circlip ftom under tank ????
It took to the air doing the filter. _________________ 1994 K1100 LTSE + Blackbird |
|
Back to top |
|
|
|